Tecomec GEOline 8410073 Скачать руководство пользователя

Страница: 25 / 68

ISOBUS ECU 1224 User and Instruction maual

P00801545 Rev:02 SW:1.0.0

ISO-15

ISO-20

Custom 1

(*)

Custom 2

(*)

Main valve type

Type of main valve

Bypass

Dump

Main valve driver

How the main valve is managed

Independent

Dependent

Regulation valve type

Define what time of regulation valve
is installed in the control unit

Bypass (3 ways)

Throttling (2 ways)

Section valve type

ON-OFF

OFF-ON

ON-OFF met.

OFF-ON met.

Section valve wires

Number of Wires for each valve

2 Wires: Polarity inversion

3 Wires : Power and driving pin.

Note: Require correct type of
harness.

2 or 3

Sections control

Modify the way section valves are
manually opened/closed (refer
Chapter 10.4 for a description of
these parameters)

Standard

Extended

Tank level sensor present

Tank level sensor presence/absence

yes/no (check box)

Reserve level

Number of liters of the tank reserve

0 ÷ 10000

Tank capacity

Tank capacity in liters

0 ÷ 20000

Offset Y

(**)

Distance of the center of the spray
bar, relative to the center axis facing
in the direction of movement (mm)

–

positive if moved to the right and
negative when moved to the left

-100,00 ÷ 100,00

Содержание GEOline 8410073





































































Результаты поиска

Содержание GEOline 8410073

Отзывы:

Похожие инструкции для GEOline 8410073

Бренды по названию

Популярные бренды

Tecomec GEOline 8410073, Инструкция и руководство пользователя

Результаты поиска

Содержание GEOline 8410073

Отзывы:

Похожие инструкции для GEOline 8410073

Бренды по названию

Популярные бренды