Tecomec GEOline 8410073 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 68

background image

ISOBUS ECU 1224 User and Instruction maual

|

P00801545 Rev:02 SW:1.0.0

29

The flow-meter output is captured by the ISOBUS ECU 1224 and is represented by a pulsing signal
with a frequency proportional to the measured flow. In order to determine the flow, it is

necessary to configure the “Flow

-

meter conversion factor” representing the

amount of pulses

corresponding to one liter. This parameter can be found on the flowmeter documentation.

This parameter depends on the flowmeter and the conversion factor may vary according to the
sensor range and/or constructor.

The configuration page contains also the “flow

-

meter min/max value” parameters that are used by

system for graphical and consistency check purposes.

We recommend the use of Tecomec flowmeters having the following characteristics:

Part No. l/1’ bar

% FSO

°C V dc

#8404012 range (10÷200) l/min
#8404023

range (3÷60) l/min

#8404024

range (5÷100) l/min

#8404025

range (10÷200) l/min

In

“

WORK

”

page (fig 20),t the flow is reported in the indicator (lower left area)

That indicator can be used to show the measured pressure. To show the flow in the WORK page
check

the “Show press/flow” parameter must be set to “flow”).

9.3.4 Pressure sensor setup

The pressure sensor is optional Can be used to measure the pressure in the control unit or
regulate the Ratio. Check specific parameters in the SETUP Page If the sensor pressure is present,

the “Pressure sensor min/max value” parameters shall be defined.

The pressure sensor must supply signal 4-20 mA, proportional to pressure.

9.3.5 Tank level sensor setup

This sensor is Optional.

ECU-1224 can manage a level sensor (4-20 mA output) mounted on the sprayer tank, to
determine the current level of the agronomic product available.

In case level sensor is installed,

enable “Tank level sensor present” parameter of the configuration.

After sensor installation run level sensor calibration (refer to chapter 9.7 for more details).

If the use of the level sensor is disabled, ISOBUS ECU 1224 calculates tank level using flowmeter to
determine the amount of product distributed and consequently the residual quantity available in
the tank.

«
...
28
29
30
31
32
...
»

Содержание GEOline 8410073





































































Отзывы:

Нет отзывов

Похожие инструкции для GEOline 8410073

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Watts Страницы: 4

Бренд: Samson Страницы: 102

Бренд: Climatisation Страницы: 52

Бренд: TECOM Страницы: 8

Бренд: Grundfos Страницы: 23

Бренд: Sungrow Страницы: 4

767-4803/000-800

Бренд: WAGO Страницы: 80

Бренд: S&C Страницы: 24

Бренд: Valence Tech Страницы: 12

Бренд: Dungs Страницы: 56

Бренд: Emec Страницы: 8

Бренд: Atmel Страницы: 12

Бренд: Phoenix Contact Страницы: 56

Бренд: Danfoss Страницы: 10

Бренд: SimCom Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды