Tecomec GEOline 8410073 Скачать руководство пользователя страница 7

Страница: 7 / 68

ISOBUS ECU 1224 User and Instruction maual

P00801545 Rev:02 SW:1.0.0

WARNING

: Disconnect power supply ECU before reparations, or welding

procedure on the vehicle. If it is not the case, Tecomec s.r.l is not responsible for
damages to the ECU.

WARNING

: For a correct functioning, please make sure that the battery voltage

is higher than 10, 5 Volt.

WARNING: This marking on the product or on its packaging
illustrates that this product may not be disposed of with
normal household waste.

The user is responsible for the disposal of this equipment
through a designated collection of electrical and electronic
equipment. To determine where to dispose of such electrical and electronic

waste, contact the government office, the waste disposal organization serving the family, or the
company where the product was purchased.

WARNING

: Before cleaning the implement with high pressure water jets,

protect the equipment from water. Do not orientate high pressure water jet
directly on ECU or cables connected to ECU.

WARNING

: Clean equipment using a soft, damp, lint-free cloth. Do not use

sprays, solvents, abrasives, or sharp or pointed objects that could damage
equipment

WARNING:

Before operating or installing this equipment read and understand

manual and all safety information. Good safety practices protect operators from

Содержание GEOline 8410073





































































Результаты поиска

Содержание GEOline 8410073

Отзывы:

Tecomec GEOline 8410073, Инструкция и руководство пользователя, Страница: 7 / 68

Результаты поиска

Содержание GEOline 8410073

Отзывы: