Tecomec GEOline 8410073 Скачать руководство пользователя страница 40

Страница: 40 / 68

ISOBUS ECU 1224 User and Instruction maual

P00801545 Rev:02 SW:1.0.0

Following the description of LED Status

Table 13

Status

LED Light description

Off

Always turned OFF

Always turned ON

Flash Slow

1500 ms ON, 1500 ms OFF

Flash Normal

700 ms ON, 700 ms OFF

Flash Fast

250 ms ON, 250 ms OFF

Pulse 1

One pulse (200 ms ON, 200 ms OFF)followed 1000 ms OFF

Pulse 2

Two pulses (200 ms ON, 200 ms OFF) followed 1000 ms OFF

Pulse 3

Three pulses (200 ms ON, 200 ms OFF) followed 1000 ms OFF

Pulse 4

Four pulses (200 ms ON, 200 ms OFF) followed 1000 ms OFF

9.8.1 Led L1: main status

L1 display the status of the ISOBUS ECU 1224. The following notation is used:

•

IDLE status

: the driver is ready, but no treatment is running

→

Flash SLow

•

WORK status

: the driver is managing a treatment (main valve open)

→

Flash Fast

9.8.2 Led L2: ISOBUS connection status

L2 display the current connection status of the ISOBUS ECU 1224 with the ISOBUS network. The
following notation is used:

•

OFFLINE status

: the ISOBUS network is not detected

→

Flash Fast

•

ONLINE status

: the ISOBUS network is detected

→

9.8.3 Led L3: error codes

L3 display the last error code detected by the ISOBUS ECU 1224 driver. It uses the

Pulse 1÷4

modes to indicate specific errors and the

Off

state for no errors.

Содержание GEOline 8410073





































































Результаты поиска

Содержание GEOline 8410073

Отзывы:

Похожие инструкции для GEOline 8410073

Бренды по названию

Популярные бренды

Tecomec GEOline 8410073, Инструкция и руководство пользователя

Результаты поиска

Содержание GEOline 8410073

Отзывы:

Похожие инструкции для GEOline 8410073

Бренды по названию

Популярные бренды