TC Electronic FireworX Скачать руководство пользователя

Страница: 57 / 83

THE BLOCKS

Drive*

The Drive parameter simulates the Input gain of a distortion

device. The extra Input gain is automatically compensated on

the Output level to avoid any clipping internally.

Brightness*

Brightness is used to reduce the amount of high frequency

content in the distorted signal. The Brightness control is flat

when set to 100%.

Body*

Body is used to reduce the amount of low frequency content

in the distorted signal. At heavy distortion the Drive will

emphasize a lot of low frequencies, which can be somewhat

annoying. These problems can be reduced by the Body

parameter. A number of preamps and pedals on the market

combine a lowcut filter with their Input gain to compensate

for the exact same problem.

Smasher*

The Smasher is used to change the character of the distortion

by emphasizing even order harmonics. Setting this parameter

to a high value, will smash your signal. Try experimenting

with the character of your distortion.

Out Drive*

Out Drive is simulating the kind of distortion that you would

get from the output stage of an amplifier.

Mix*

Mixes between direct sound and effect.

In Level*

Controls the input level of the block.

Out Level*

Controls the output level of the Drive block.

Cruncher

The Cruncher performs both Aliasing and Quantizing

simultaneously.

Aliasing is a residual artifact of digital conversion that was

common in the early days of the digital world. In the

FireworX this artifact is magified into an effect. Sound-wise,

the Aliasing appears as an unharmonic, fairly high frequency

distortion.

The Quantizer produces an artificial noise floor as if the

signal had been sampled at a lower bit resolution.

The parameters available in the Modifier Matrix are marked

with an asterisk*.

CRUNCHER

Aliaser Factor*

Sets the sample rate reducing-factor, and thereby enhances

the Aliasing artifacts.

Aliaser level*

The level of the Aliaser signal

Quantize grain size*

Sets the grain size or reduces the bit resolution that is used

to quantize the signal.

Quantize level*

The level of the Quantized signal.

In Locut*

Cuts off frequencies lower than the selected frequency on

the input. The slope of the filter is 12dB/octave.

Range: 10Hz-16kHz.

In Hicut*

Cuts off frequencies higher than the selected frequency on

the input. The slope of the filter is 12dB/octave.

Range: 10Hz-16kHz.

Out Locut*

Cuts off frequencies lower than the selected frequency on

the output. The slope of the filter is 12dB/octave.

Range: 10Hz-16kHz.

Out Hicut*

Cuts off frequencies higher than the selected frequency on

the output. The slope of the filter is 12dB/octave.

Range: 10Hz-16kHz.

Mix*

Mixes between direct sound and effect.

In Level*

Controls the input level of the block.

Out Level*

Controls the output level of the Drive block.

Vocoder

Number of blocks: 1

Processing power: 33-46% per block

The Vocoder block contains two different types of effects:

Vocoder and Ring Modulator. Both of these effects are Dual

Содержание FireworX




















































































Результаты поиска

Содержание FireworX

Отзывы:

Похожие инструкции для FireworX

Бренды по названию

Популярные бренды

TC Electronic FireworX, Руководство пользователя

Результаты поиска

Содержание FireworX

Отзывы:

Похожие инструкции для FireworX

Бренды по названию

Популярные бренды