TC Electronic FireworX Скачать руководство пользователя

Страница: 52 / 83

Ratio

The Ratio of the gain reduction. Example: When the Ratio is

set to 4:1 it means that for every 4dB the input level rises, the

output level increases by only 1dB.

Knee Mode

The Knee Mode parameter sets the bending point of the

compressor to soft knee or hard knee. When soft knee is

selected, the Compressor will gradually reach the Ratio,

while hard knee will cause the Compressor to go directly

from no compression to the current Ratio.

Release

Release sets the fall back time of the Compressor, after the

signal drops below the Threshold, meaning if the Compressor

is reducing the gain by 14dB and the Release is set to

28dB/S, it will take 0.5 second before the Compressor

reaches no gain reduction af the signal dropped below

threshold.

Gain

The Gain parameter makes it possible to compensate for the

loss of level in the Compressor. This is also known as

Makeup gain.

In Level*

Controls the input level of the block.

Out Level

Controls the output level of the Compressor block.

LED Meter

If more than one Dynamics block is present in the Routing,

this parameter determines which one will be displayed by the

Gain reduction meter on the front panel.

Hard Compressor/Limiter

The Hard Compressor/Limiter is somewhat similar to the Soft

Compressor. One of the main differences is that the

Compressor/Limiter responds to the peak level whereas the

Compressor responds to the RMS average level. Peak

compression in general is a bit more aggressive sounding.

The parameters available in the Modifier Matrix are marked

with an asterisk*.

HARD COMPRESSOR/LIMITER

Threshold

When the input level exceeds the Threshold, the Compressor

will be activated. This means that the lower the Threshold,

the more compression you will get.

COMPRESSOR/LIMITER

Ratio

The Ratio of the gain reduction. Example: When the Ratio is

set to 4:1 it means that for every 4dB the input level rises,

the output level increases by only 1dB.

Attack

Attack is the amount of time that the Compressor uses to

reach the gain reduction specified by the Ratio parameter.

Example: The Input signal rises 4dB above threshold in no

time, with the Ratio set to 1:4 and the Attack set to 20ms.

The Compressor will now use 20ms to reach the 3dB gain

reduction.

Release

Release sets the fallback time from when the input signal

falls below threshold till the Compressor/Limiter reaches no

gain reduction.

Gain

The Gain parameter makes it possible to compensate for the

loss of level in the Compressor/Limiter. This is also known

as Makeup gain.

Mix

Mix between direct sound and effect sound.

In Level*

Controls the input level of the block.

Out Level

Controls the output level of the block.

LED Meter

If more than one Dynamics block is present in the Routing,

this parameter determines which one will be displayed by

the Gain reduction meter on the front panel.

THE BLOCKS

Содержание FireworX




















































































Результаты поиска

Содержание FireworX

Отзывы:

Похожие инструкции для FireworX

Бренды по названию

Популярные бренды

TC Electronic FireworX, Руководство пользователя

Результаты поиска

Содержание FireworX

Отзывы:

Похожие инструкции для FireworX

Бренды по названию

Популярные бренды