Tartan 4100 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 54

Tartan 4100 Скачать руководство пользователя страница 9

T4100 OM rev2

Page 9 of 50

After Shakedown Sail:

9

Re-tension all rigging if necessary .

9

If excess headstay sag is apparent adjust the headstay and/or backstay tension as required.

Again, this manual is intended to help you to know your new Tartan Yacht. It is most important to
familiarize yourself thoroughly with all aspects of operating and maintaining your yacht in a safe and
efficient manner. Read your manual carefully as well as the booklets supplied by the manufacturers of
the components. If any questions arise for which you can’t find an answer, your Tartan dealer will be
pleased to help you.

It is Company policy that the Tartan line of yachts is continually upgraded and improved. Therefore, you
may find your yacht equipped with gear different from that shown in your manual. Any new piece of
equipment will be in all cases equal to or better than, its predecessor.

On taking delivery of your yacht, be sure to read and understand the Tartan warranty. Complete the
warranty registration and return it to Tartan immediately.

If you are a seasoned sailor much of the manual may be old news but if this is your first boat, we hope
this will prove useful. We know that you will have many satisfying and happy hours of sailing in your
Tartan Yacht.

Should you need to contact Tartan Yachts please use the following addresses and numbers:

Tartan Yachts

Customer Service

1920 Fairport Nursery Road

Fairport Harbor, OH 44077

Phone: 440-354-3111

Fax: 440-354-6162

Websites: www.tartanyachts.com and www.tartanparts.com

We would like to take this opportunity to thank you for choosing Tartan Yachts and we wish you good
sailing.

«
...
7
8
9
10
11
...
»

Содержание 4100























































Отзывы:

Нет отзывов