
T4100 OM rev2
Page 35 of 50
wire strands, cracked swage terminals or nicks, scratches and dents in rod rigging. Inspect all clevis pins
for wear, and to be certain that they are properly pinned and taped so that they do not damage sails or
halyards. Consult your Tartan Dealer if you detect any potential problem.
b) Install the spreaders and secure the rigging to the spreader ends. Be sure the halyards are not
entangled with the spreaders. Pad the spreader ends with foam and tape over thoroughly to prevent chafe
to the sails. Test all mast lights with a portable 12 Volt battery and label all wires at the mast base
accordingly. Tie all running rigging together and secure the bundle to the spar at the lower black band.
Tie all standing rigging together and secure the bundle to the spar at the lower black band. Remove cotter
and clevis pins from all turnbuckles and place them in a container for future use. Back off all turnbuckles
and lightly grease the threads of the turnbuckle screws with a corrosion inhibitor such as Lanocote or Tef
Gel. If the turnbuckle threads have tape adjustment marks, do not remove the tape or alter the positioning
by adjusting the turnbuckle unevenly.
DOUBLE CHECK EACH OF THE ABOVE STEPS BEFORE PROCEEDING.
c) Prepare a rope sling, of adequate capacity, which will take the weight of the spar. Place the sling
INSIDE the standing and running rigging so that it will not crush the rigging against the spar. Next, make
fast a ½” diameter tie-down line to the sling, securing the line at the lower end of the spar. Ensure that
the tie-down will not interfere with the removal of the bundle of standing rigging which will be undone
before the sling is removed. To prevent the weight of the spar being carried by the spreaders or mast
hardware when the spar is raised to a vertical position, adjust the tie-down so that the weight of the spar is
carried by the sling and tie-down only.
d) Attach the crane lifting hook to the sling. It is recommended that a piece of carpet be wrapped and
taped around the lifting hook to prevent it from marking the mast during stepping.
DO NOT STAND OR POSITION ANYONE DIRECTLY BELOW A SUSPENDED MAST.
At least three persons in addition to the crane operator should be present when stepping the spar. Position
one person at the foot of the mast to guide the foot as the mast is being lifted, slowly swing the crane
toward the yacht while keeping the foot pointed toward the base of the crane. This will keep the spar
from swinging into the crane.
DO NOT PLACE HANDS, ARMS OR FEET DIRECTLY BELOW THE SPAR AS IT IS
LOWERED INTO THE YACHT.
When the crane is in position, move the foot of the spar over to the second person who should now be
aboard the yacht. Carefully pass the spar to the person aboard. Slowly raise the spar to an almost vertical
position and guide the foot through the mast collar. Pad the mast collar with cloth to ensure that the paint
on the mast is not damaged as the mast is lowered through the collar. Be careful not to let the masthead
swing and hit the crane arm. When lowering the mast through the collar, all mast electrical wiring should
precede the entry of the mast. Check aloft that the mast and crane are not fouling. With the foot of the
mast through the collar, untie the bundle of standing rigging and clear each piece away from the crane
lifting cable.
e) Lower the mast through the collar, being careful not to scratch the mast as it passes through the collar
opening. A piece of carpet placed between the sides of the mast and the collar will reduce the likelihood
of scratching as the mast is lowered to the step. With the weight of the spar on the step, attach the
forestay, backstay and both port and starboard upper shrouds. When stepping the mast for the first time,
follow the instructions in the SparTite kit included with your new yacht.
Содержание 4100
Страница 11: ......
Страница 12: ......
Страница 13: ...6 0 W L...
Страница 47: ...T4100 OM rev2 Page 43 of 50 Tartan Yachts Commissioning Checklist...