manualshive.com logo in svg

Tartan 4100, Руководство пользователя, Страница: 19 / 54

Поделиться
Скачать
Tartan 4100 Скачать руководство пользователя страница 19

 

T4100 OM rev2 
 

Page 15 of 50

Table 5 – RECOMMENDED MAINTENANCE 

 

Note:  The items listed in the recommended 

maintenance schedule are not covered under warranty. 

 

Page (1) 

UPON 

DELIVERY 

(By Dealer) 

AFTER 

SHAKEDOWN 

CRUISE 

AT EACH USE 

EVERY (6) SIX 

MONTHS 

EVERY (12) 

TWELVE 
MONTHS 

SPARS, RIG AND SAILS 

 

 

 

 

 

Watch for chafing at spreader 

tips, pulpit and shrouds. 

X X

 

X

 

 

 

Secure turnbuckles and clevis 

pins with cotter pins and 

protect with tape. 

X

 

 

 

 

X

 

Tune or re-tune rigging. 

X

 

X

 

 

 

X

 

Inspect all rigging, deck 

fittings for cracks, crevices, 

deterioration, kinks, or other 

unusual conditions. 

X

 

 

 

X

 

 

Make sure all rigging functions 

correctly. 

X

 

 

X

 

 

 

Clean or lubricate sheaves as 

required. 

 

 

 

X

 

 

Strip down, clean and lubricate 

winches 

 

 

 

 

X

 

Rinse off blocks, sheets, lines 

and furling unit drum. 

 

 

X

 

 

 

ENGINE 

 

 

 

 

 

Check all hose clamps, cable 

straps, mounting bolts and 

shift/throttle linkages for 

tightness. 

X

 

X

 

 

X

 

 

Check engine and gear oil 

level. 

X

 

 

X

 

 

 

Check fuel level and water 

accumulation in 

filter/separator. 

X

 

 

X

 

 

 

Check coolant level. 

X

 

 

X

 

 

 

Check all warning lamp 

functions. 

X

 

 

X

 

 

 

Check for seawater discharge 

at exhaust. 

X

 

 

X

 

 

 

Inspect engine for oil leak or 

water leaks. 

X

 

 

X

 

 

 

Inspect and clean raw water 

intake strainer. 

 

 

X

 

 

 

Replace engine mounted fuel 

filter and remote filter 

separator element. 

 

 

 

 

X

 

Содержание 4100























































Отзывы:

Нет отзывов