TallyGenicom 6800 Series Скачать руководство пользователя страница 96 | Manualshive

Страница: 96 / 258

TallyGenicom 6800 Series Скачать руководство пользователя страница 96

96

Chapter

4

Config Menu

DC3 Operation

(Available when Genicom ANSI emulation is selected)

This parameter allows DC1 - DC3 operation. When set to Enable (the
default), the printer can be selected and deselected using DC1 and DC3
control codes. The printer select/deselect operation is not in effect when set to
Disable.

SISO OverszBar

(Available when Genicom ANSI emulation is selected)

This parameter allows SI-SO operation for barcodes and oversize characters.
When set to Disable (the default), barcode and oversize character modes do
not need to be activated with SO and deactivated with SI. When set to
Enable, barcode and oversize character modes will be activated and
deactivated using the SO and SI control codes.

Barcod Top Pos

(Available when Genicom ANSI emulation is selected)

When set to Enable (the default), the paper position is reset to the top of the
bar code after printing. When set to Disable, the paper position is left at the
end of the bar code after printing.

Oversz Top Pos

(Available when Genicom ANSI emulation is selected)

The paper position will be reset to the top of the oversize characters after
printing when this parameter is set to Enable (default). When set to Disable,
the paper position is left at the end of the oversize characters after printing.

«
...
94
95
96
97
98
...
»

Содержание 6800 Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды