manualshive.com logo in svg

TallyGenicom 6800 Series, Руководство администратора

Поделиться
Скачать
TallyGenicom 6800 Series Скачать руководство пользователя страница 182

182

Chapter

8

Diagnostics for EXX, BAD NVM, or ILL NVM Errors

PROCESSOR HALTED
EC_FAULT_RTSYS2

No

Real-time System 
Firmware error on 
controller board.

Contact your authorized 

service representative.

1

PROTECTED INSTR*

No

Protected Instruction. 
Firmware error on 
controller board.

Contact your authorized 

service representative.

1

PWR SUPP VOLT *

No

Power Supply Voltage. 
The power supply has 
failed.

Replace power supply board.

REMOVE USED SPX

 

THEN PRESS ENTER

No

Status message: An SPX 
is depleted because it 
has successfully 
reprogrammed the 
security key on the 
controller board.

Contact your authorized 

service representative.

1

RESTORING BOOT CODE

No

Normal download 
initialization message.

No action is required.

RIB INVLD CMD*

 

See User Manual

Yes

Ribbon Invalid 
Command. Firmware 
error on the controller 
board.

Cycle power. Run the print job 
again. If the message appears, 
download the emulation 
software again. If the message 
appears again, contact your 
authorized service 

representative.

1

RIBBON STALL

Yes

The controller board does 
not detect ribbon 
movement.

Check the ribbon path for 
jams. Turn the Ribbon Tension 
Knob clockwise a few 
rotations. If necessary, install a 
new ribbon.

RIBBON UNDER 2%
Change RBN Soon

Yes

Status message 
indicating the Integrated 
Print Management 
System is enabled and 
ribbon ink level is 2%.

Install a new ribbon.

SD CARD ERROR
Remove SD Card

Yes

The printer has been 
powered up with a card in 
the SD slot, but the card 
is not functioning 
properly. The card could 
be a compact flash card 
or a non-supported card.

Power down, reseat card, and 
power up again. If error 
persists, power down, remove 
card, and try another card.

Table 13. LCD Message Troubleshooting Table

Displayed Message

Can User 

Correct?

Explanation

Solution

Содержание 6800 Series



































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды