TallyGenicom 6800 Series Скачать руководство пользователя страница 152

Страница: 152 / 258

152

Chapter

Sending Firmware in Download Mode

10. Select the “Network Adaptors” and expand the selection if necessary.

“Microsoft Loopback Adaptor” is listed. Leave all settings as default.

You are now finished and may proceed as outlined in “Sending Firmware via
USB” on page 147.

Sending Firmware via Parallel

This method of download can be completed with firmware in the form

FILENAME.exe

FILENAME.prg

IMPORTANT

You need the parallel option installed.

Copy the firmware to the printer by entering these commands at the
Command prompt:

copy /b

FILENAME.prg

lpt1:

<Enter>

where

FILENAME.prg

is the target firmware

FILENAME –pb

<Enter>

where

FILENAME

.exe is the target firmware

IMPORTANT

DO NOT interrupt the download process once it has started. Interrupting
a download will leave the flash memory on the controller PCBA and NIC
incompletely loaded, and the printer may not boot up.

The process is complete when the new software is successfully loaded into
flash memory and the printer has reset itself.

Содержание 6800 Series



































































































































































































































































Результаты поиска

Содержание 6800 Series

Отзывы:

Бренды по названию

Популярные бренды

TallyGenicom 6800 Series, Руководство администратора

Результаты поиска

Содержание 6800 Series

Отзывы:

Бренды по названию

Популярные бренды