Takeuchi TB175W Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 221

background image

1

It is your responsibility to observe all pertinent laws and regulations and to follow the
manufacturer’s instructions on machine operation, inspection and maintenance.

Virtually all accidents occur as the result of a failure to observe basic safety rules and precautions.
An accident can often be avoided by recognizing potentially hazardous situations beforehand.
Read and understand all of the safety messages which explain how to prevent these accidents
from occurring. Do not operate the machine until you are sure that you have gained a proper
understanding of its operation, inspection and maintenance.

�

SlGNAL WORDS

Safety messages appearing in this manual and on machine decals are identiﬁed by the words
“DANGER”, “WARNING” and “CAUTION”. These signal words mean the following:

IMPORTANT: The word “IMPORTANT” is used to alert against operators and maintenance
personnel about situations which can result in possible damage to the machine and its
components.

It is impossible to foresee every possible circumstance that might involve a potential hazard.
The warnings in this manual or on the machine can not cover all possible contingencies. You
must exercise all due care and follow normal safety procedures when operating the machine
so as to ensure that no damage occurs to the machine, its operators or other persons.

�

EXPLANATION OF GRAPHICAL SYMBOLS

Following is an explanation of symbols used in this manual.

, X ..........prohibition

............lock

............unlock

The  word  “DANGER”
indicates an imminently
hazardous  situation
which, if not avoided,
can  result  in  serious
injury or death.

The word “WARNING”
indicates a potentially
hazardous situation
which, if not avoided,
could result in serious
injury or death.

The word “CAUTlON”
indicates a potentially
hazardous situation
which, if not avoided,
may result in minor or
moderate injury.

CAUTION

WARNING

DANGER

«
1
2
3
4
5
...
»

Содержание TB175W






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB175W

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 51

Бренд: New Holland Страницы: 51

Бренд: Komatsu Страницы: 284

Бренд: Greyhound Страницы: 61

PRINCESS M1- MR

Бренд: Grillo Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды