Takeuchi TB175W Скачать руководство пользователя страница 59 | Manualshive

Страница: 59 / 221

background image

57

CONTROLS

Levers and Pedals

Swing Lock Pin

To lock the hoe attachment and upperstructure
for transport and on-road driving use the pin
as follow:
1. Lift the pin (1) out of the bracket near the

operator’s seat.

2. Swing the coupling (2) forward.
3. Align equipment and upperstructure.
4. Lower the pin (1) fully into the lock.

IMPORTANT:  Operation of the excavator
and  slewing  of  the  upperstructure  is
possible only if the pin is in the bracket
near the operator’s seat. A side from small
correctional  movements,  any  swinging
can result in damage to the machine.

Safety Lock Lever

WARNING

�

Before leaving the operator’s seat, set

the safety lock lever securely to the
lock position and stop the engine. If any
controls should be touched accidentally
when the safety lock lever has not be
locked, the machine will move suddenly,
and cause serious injury or death.

�

Note that the dozer blade control is not

locked, even when the safety lock lever
is set to the lock position. Do not touch
this control accidentally.

�

Be careful not to touch the operating

levers when raising and lowering the
safety lock lever.

This device is for locking the hoe attachment,
auxiliary hydraulic systems and slewing.
When the lever is lifted, the lever stand springs
up and the lever is locked.

W2B023

1

2

W2B024

«
...
57
58
59
60
61
...
»

Содержание TB175W






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB175W

Бренд: Yuchai Страницы: 131

Бренд: Promeba Страницы: 50

Бренд: Doosan Страницы: 207

Бренд: Doosan Страницы: 211

Бренд: SANY Страницы: 228

Бренд: Takeuchi Страницы: 231

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды