Takeuchi TB175W Скачать руководство пользователя страница 116

Страница: 116 / 221

114

MAINTENANCE

Walk-Around Inspection

Inspecting by Opening the Engine
Hood and Covers

1. Check for any twigs, leaves, oil or other

combustible materials around the engine
and battery.

2. Check for oil or engine coolant water

leakage around the engine.

3. Check for oil leakage from the hydraulic

tank, hydraulic devices, hoses and
connections.

Perform the following inspections once every day before starting the engine the ﬁrst time.

WARNING

�

Before operating, perform the walk-around inspections and make repairs immediately

should any irregularities be found.

�

Be sure to secure the engine hood or cover when opening it. Do not open the engine

hood or cover on slopes or in strong wind.

Before starting the engine, look around the machine and lower body, clean any combustible
materials off high temperature parts of the engine, and inspect for such irregularities as oil
leakage, water leakage and looseness of nuts and bolts.

Содержание TB175W






























































































































































































































Результаты поиска

Содержание TB175W

Отзывы:

Похожие инструкции для TB175W

Бренды по названию

Популярные бренды

Takeuchi TB175W, Руководство оператора

Результаты поиска

Содержание TB175W

Отзывы:

Похожие инструкции для TB175W

Бренды по названию

Популярные бренды