Takeuchi TB175W Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 221

background image

70

OPERATION

Before Starting Operation

Walk-Around Inspection

Perform the walk-around inspections once a
day before starting the engine the ﬁrst time
that day.
Perform the inspections as descrAbed under
“Maintenance - Walk-Around Inspection”
(pages 114 and 115).

Daily Inspection

Perform the daily inspections once a day
before starting the engine the ﬁrst time that
day.
Perform the inspections as described under
“Maintenance - Daily Inspection” (pages
116 to 122).

Mounting and Dismounting

WARNING

�

Do not jump on or off the machine.

Never attempt to mount or dismount a
moving machine.

�

When mounting and dismounting the

cab, first open the door fully to the
locked position and check that it does
not move.

�

Always face the access system and

maintain a three point contact with
the recommended handrails and steps
while getting on and off the machine.
Keep steps and platform clean.

�

Never use the safety lock lever or

control levers as hand holds.

W2D001

W2D029

«
...
70
71
72
73
74
...
»

Содержание TB175W






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB175W

Бренд: Rail-Ability Страницы: 64

Бренд: Yanmar Страницы: 95

Бренд: jcb Страницы: 15

Бренд: Wacker Neuson Страницы: 29

Бренд: Werk-Brau Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды