Takeuchi TB175W Скачать руководство пользователя страница 135 | Manualshive

Страница: 135 / 221

background image

133

MAINTENANCE

Every 400 Hours

Inspecting the Transmission Gear
Oil

WARNING

�

Stop the engine and allow the machine

to cool down before performing
maintenance.
• The transmission are hot directly after

the engine is stopped. Touching them
will cause burns.

• The gear oil is also hot and under high

pressure.

Be careful when loosening plugs.

Working on the machine under these
conditions could result in burns or
injuries.

�

The  pressure  in  the  transmission
reduction  gears  case  may  cause  oil
or the plug to ﬂy out.  Loosen the plug
slowly to release the pressure.

1. Park the machine on a level surface. Stop

the engine.

2. Remove the plug (1) from the transmission

housing.

3. If oil can be reached with the tip of the

your ﬁnger through the hole, the oil level
is correct.

4. If the level is low, add oil through the check

plug hole until the oil ﬂows from the hole.

5. Install and tighten the plug.

Inspecting the Differential Gear
Oil

WARNING

�

Stop the engine and allow the machine

to cool down before performing
maintenance.
• The differential are hot directly after

the engine is stopped. Touching them
will cause burns.

• The gear oil is also hot and under high

pressure.

Be careful when loosening plugs.

Working on the machine under these
conditions could result in burns or
injuries.

�

The pressure in the differential gears

case may cause oil or the plug to ﬂy
out. Loosen the plug slowly to release
the pressure.

1. Park the machine on a level surface. Stop

the engine.

2. Remove the plug (1) from the differential

housing.

3. If oil can be reached with the tip of the

your ﬁnger through the hole, the oil level
is correct.

4. If the level is low, add oil through the add

plug hole (2) until the oil ﬂows from the
hole.

5. Install and tighten the plug.

W2G0161

1

W2G017

OIL

Oil level

Ölstand

2

1

«
...
133
134
135
136
137
...
»

Содержание TB175W






























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для TB175W

Бренд: Camon Страницы: 20

Бренд: Greyhound Страницы: 61

Бренд: Komatsu Страницы: 8

Бренд: Daewoo Страницы: 670

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды