Takeuchi TB175W Скачать руководство пользователя страница 143

Страница: 143 / 221

141

MAINTENANCE

Replacing the Hub Gear Oil

WARNING

�

Stop the engine and allow the machine

to cool down before performing
maintenance.
• The hubs are hot directly after the

engine is stopped. Touching them will
cause burns.

• The gear oil is also hot and under high

pressure.

Be careful when loosening plugs.

Working on the machine under these
conditions could result in burns or
injuries.

�

The pressure in the hubs reduction

gears case may cause oil or the plug
to ﬂy out. Loosen the plug slowly to
release the pressure.

1. Set the hub so that the plug (1) is at the

very bottom.

2. Park the machine on a level surface. Stop

the engine.

3. Place a pan for catching the spent oil under

plug (1).

4. Remove plug (1) and drain the oil.
5. Set the hub so that plug (1) is at the level.

Every 1500 Hours

6. Supply oil through the hole for plug (1) until

oil ﬂows out of the hole of plug (1).

7. Tighten plug (1).

W2G0211

W2G018

OIL

Inspecting and Cleaning the
Engine Fuel Injectors

This operation requires experience. Have
it performed by a Takeuchi sales or service
outlet.

Inspecting the Turbocharger
(Blower wash as necessary)

This operation requires experience. Have
it performed by a Takeuchi sales or service
outlet.

Inspecting and Cleaning the EGR
Valve, Lead Valve and Cooler

This operation requires experience. Have
it performed by a Takeuchi sales or service
outlet.

Inspecting the Crankcase
Breather System

This operation requires experience. Have
it performed by a Takeuchi sales or service
outlet.

Содержание TB175W






























































































































































































































Результаты поиска

Содержание TB175W

Отзывы:

Похожие инструкции для TB175W

Бренды по названию

Популярные бренды

Takeuchi TB175W, Руководство оператора

Результаты поиска

Содержание TB175W

Отзывы:

Похожие инструкции для TB175W

Бренды по названию

Популярные бренды