manualshive.com logo in svg

Synel PrintX-FPR, Руководство по эксплуатации продукта, Страница: 37 / 39

Поделиться
Скачать
Synel PrintX-FPR Скачать руководство пользователя страница 37

 

                                                                                                                                                                                                Back to Table of Contents

37 

Mode” enter “13” followed by a eight digit number that will serve as a new master Code.

Note: It is recommended to change master code when setting up.

Erase All

After entering the “Programming Mode,” enter “6” and then eight digits Master code.

 Warning! Cards can not be restored after they are erased!

1.2.7 Indicators definitions

After entering setup mode:

Input Operation Mode

Code 30 -->0 = Door open request button

As a result the door will open and the output = bypass
1 = Door sensor
As a result the output = alarm will be activated (led/buzzer)

Sensor type

Code 31-->0 = The sensor will function as Normally Open.

1 = The sensor will function as Normally Closed.

Alarm mode

Code 51--> 0 = Latch. The alarm does not go off unless it is turned off

manually.
1 = Pulse. The alarm goes off after the defined time-out.

Alarm pulse activating time

Note: Relevant when alarm is in pulse mode.

Code 52--> 0000-9999 seconds (always key-in time in 4 digits format)

Sensor door activating time

Содержание PrintX-FPR








































Отзывы:

Нет отзывов