Synel PrintX-FPR Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 39

Synel PrintX-FPR Скачать руководство пользователя страница 29

Back to Table of Contents

29

14.0.1Access Control using PrintX-FPR

3. Place the user-finger on the fingerprint sensor.
4. A fingerprint recognized as matching a fingerprint template stored in the unit allows access -

activates door relay.
An un-recognized fingerprint denies access and initiates a buzzer sound - door relay is not
activated.

14.0.2FPU operation - Instructions and Best practices

1. Do not use your thumb to enrol.

2. Place the higher joint of your finger on the ridge lock and lower your finger onto the sensor

surface (make sure all other fingers are held straight to avoid creating an angle between the
enrolled finger and the sensor surface - incorrect positioning).

3. Touch the sensor's plastic casing (black) in order to discharge static electricity. Keep your finger

steady!

4. Press your finger gently onto the panel, avoid excessive pressure as it will blur the print.
5. Make sure your finger is touching the sensor’s drive ring.
6. Use the

same

finger for enrolment as well as for verification.

7. If your finger is extremely dry, touch your forehead or the side of your nose before placing it on

the sensor.

«
...
27
28
29
30
31
...
»

Содержание PrintX-FPR








































Отзывы:

Нет отзывов