manualshive.com logo in svg

Synel PrintX-FPR, Руководство по эксплуатации продукта, Страница: 28 / 39

Поделиться
Скачать
Synel PrintX-FPR Скачать руководство пользователя страница 28

 

                                                                                                                                                                                                Back to Table of Contents

28 

14 Troubleshooting

[Question] 

If I already have a PRX-40 B and a PrintX-FPR unit can I set them up together as a standalone unit? 

[Answer]

Yes, you do not have to use the kit, you can set these units up as standalone if the following 

conditions are met:
• You need to have a reader of type FPU-S
• The firmware version of the reader needs to be version 2.08 or higher.
•  You can have either an Optic or TC (Capacity) FPU.
If these conditions are met, contact technical support to install Unifinger and change the baudrate.

[Question] 

The controller is not enrolling the fingerprints. Is there something I should check?

[Answer]

In PrintX-FPR Programming mode, check that code 36 is chosen as Auto-identify mode.

[Question] 

How can I tell if the FPU I have is Optic or TC (Capacity)?

[Answer]

You can see the difference easily according to the following characteristics:

 A capacity (TC) reader has hozinontal lines on it’s surface.  

 An optic reader has a light inside of it.

Содержание PrintX-FPR








































Отзывы:

Нет отзывов