Synel PrintX-FPR Скачать руководство пользователя страница 20 | Manualshive

Страница: 20 / 39

background image

Back to Table of Contents

20

8

Jumpers

8.1

PRX-40/B

Jumper

Function

Default

JP2 (SMD)

JP2 closed and JP3 open = 13 digits decoding

JP2 open and JP3 closed = 14 digits decoding

13 digits

JP3 (SMD)
JP4 (SMD)

Cross point decoding (currently NA)

JP7 (SMD)

Connect RS-485 termination resistor

Open

JP10 (TH)

W.D. Reset for the master CPU- [1-2] Closed

Programming of the master CPU - [2-3] Closed

[1-2] closed

JP11(TH)

PSEN (Programming) - must be closed when programming

the master CPU.

Open

JP12 (SMD)

Tamper switch enabled [1-2] closed

Tamper switch disabled [2-3] closed

[2-3] closed

JP20 (T.H)

Closed- Stand alone

Open- Online with Master

Closed

JP21 (T.H)

Contacts switching protection in DC- closed

Contacts switching protection in AC- open

Closed

JP22 (SMD)

Connecting clock to slave CPU

[2-3] closed

JP23 (T.H)

Select sensor option:

[1-2] and [3-4] Closed - dry contact

[2-3] Closed - AC/DC

[1-2] and [3-

4] closed

JP24 (T.H)

Reset for the slave/reader CPU- [2-3] closed

Programming of the slave/reader CPU [1-2] Closed

[2-3] closed

«
...
18
19
20
21
22
...
»

Содержание PrintX-FPR








































Отзывы:

Нет отзывов

Похожие инструкции для PrintX-FPR

Бренд: Facility Explorer Страницы: 4

Бренд: Jands Страницы: 6

Бренд: Vageo Страницы: 2

Бренд: HEIDENHAIN Страницы: 257

LDSBus LC020101A-F

Бренд: BRT Systems Страницы: 15

Бренд: GeoVision Страницы: 21

Бренд: Nibe Страницы: 20

Бренд: wattstopper Страницы: 4

Бренд: Digital View Страницы: 35

Бренд: Bamo Страницы: 10

Бренд: W8ZR Страницы: 77

BaseStation 1000

Бренд: Base Line Страницы: 11

Бренд: Salus Страницы: 24

Бренд: MICROMATIC Страницы: 10

Бренд: Spirax Sarco Страницы: 20

Бренд: Festo Страницы: 48

DI-DMX-WIFI-WMDC-1ZWH

Бренд: DIODE LED Страницы: 5

Бренд: ROLA-CHEM Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды