Symmetricom ATS-6511A страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

15

   [auto_rearm] true
   [master] A
   [min_valid_time] 1
   [mode] auto
[OK] 2013-08-13T17:26:23Z

The

mode

indicates the ATS-6511 is using the auto switching feature. If there is a loss

of signal on Fiber A (master) the Input A indicator will turn RED to indicate there is an issue with
that source and the system will automatically switch over to Input B and the Input B indicator will
turn ON. The

status input:switch

command will indicate an auto switch occurred as well as

which fiber is currently selected (i.e. Auto Switched: B (now in B after an autoswitch).  Once the
signals to Input A are restored the INPUT A indicator will flash Green (on for 1 second/off for
three  seconds).    When  the  master  source  (in  this  case  Input  A)  remains  valid  for  the
[min_valid_time]  (seconds-in  this  case  60)  and  the  [auto_rearm]  is  true,  the  ATS-6511  will
automatically switch back to the master source, in this case Input A becomes the active channel.

Note:

If the

[auto_rearm]

is false, the system will remain on Input B until the operator

commands the system to return to Input A. Once Input A is restored the Input A indicator will
flash Green (on for 1 second/off for three seconds) and the system will remain in this mode until
the operator commands the system to switch back to A. (

fiber_switching auto A 60

)

Caution:

The system will not switch back to the primary source unless the

manual

option is used

or until the

[min_valid_time]

has expired if you are using the

auto

mode with the

norearm

option

off.

If there is a loss of signal on Input B (the alternate source) the INPUT B indicator will turn RED
to indicate which fiber pair has been lost. Once the signals are restored the INPUT B indicator
will flash Green indicating the source is available.

When both fiber inputs are not available, the unit will enter holdover mode. In the ATS-6511A,
the internal OCXO is the holdover reference. The ATS-6511B-R provides an internal Rubidium
reference for holdover, or can use the 10 MHz provided to the rear panel as the holdover
reference. The ATS-6511B provides the user the ability to use an external input for holdover in
addition to the internal OCXO.

2.5.2 Manual Switching

When the auto switching feature is disabled the operator must select the desired input (A or B) as
the primary (master) source, in the example below Fiber A is the master. System settings can be
checked using the

settings fiber:switching

command.

ATS-6511>fiber_switching manual A

[OK] 2013-08-13T17:30:02Z

ATS-6511>settings fiber:switching

   [auto_rearm] true
   [master] A
   [min_valid_time] 30

[mode] manual

[OK] 2013-08-13T17:32:52Z

«
...
19
20
21
22
23
...
»

Содержание ATS-6511A




















































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS-6511A

Бренд: Jensen Страницы: 12

Cyber Simco Drive 2

Бренд: Wittenstein Alpha Страницы: 56

Axiom HPD3400PFC

Бренд: PROEL Страницы: 24

Бренд: Nobsound Страницы: 2

Бренд: Fender Страницы: 18

Бренд: DAPAudio Страницы: 14

Lightstar Direct

Бренд: Carver Страницы: 20

Бренд: Perreaux Страницы: 42

GTR-7535/104/102

Бренд: JBL Страницы: 38

Бренд: JB Systems Light Страницы: 11

Бренд: JBL Страницы: 14

Бренд: icon Audio Страницы: 6

Бренд: Lab 12 Страницы: 9

Tuffset Console Amplifier

Бренд: VXI Страницы: 1

Бренд: Line Magnetic Страницы: 13

Бренд: Omnitronic Страницы: 20

Бренд: Velleman Страницы: 30

Бренд: Audio Solutions Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды