Symmetricom ATS-6511A Скачать руководство пользователя страница 102

Страница: 102 / 115

DOC 6511_Release K

ATS-6511A/B/C Users Guide

enable 1 displays the prompt; 0 hides the prompt
default Change the prompt for all future sessions

Command Example:

This command changes it for the current session.

ATS-6511>prompt –text Test
Test>

Changes the prompt immediately, only in effect for the current telnet session.

ATS-6511>prompt –enable 0
Prompt is no longer visible. This change is only in effect for the current telnet session.

Command Example:

This command makes it the system default.

ATS-6511>prompt –text Test --default
ATS-6511>

Note: Prompt does not change until the next command port connection is made.

ATS-6511>prompt –enable 0 --default
ATS-6511>

Prompt is still visible, Prompt does not disappear until the next

command port connection is made.

Query:

ATS-6511>settings command_port

   [prompt]
      [enable] true
      [text] Test>

Note:

Making any changes without the –default option will impact the current session and

will not impact the system settings. Using the –default option will change the system
settings (

settings command_port

) values and will be used the next time the user makes a

command port connection. These settings must also be saved.

Ptdavg:

Description:

Set PTD averaging interval in seconds. Changes the PTD (Phase Time

Difference) averaging interval for the pulse measurement data displayed on the ptdavg_port
(port 2100). The averaging interval is applied to all of the measurement channels and can’t
be individually configured on a port by port basis.

Note

: This command is only valid when a 4393A PPS measurement module is installed in

the system.

Syntax

: ptdavg [1|10|20|60|300]

Command Example:

ATS-6511>ptd 10

Query:

ATS-6511>settings ptd_port

[averaging_interval] 10
[OK] 2010-05-25T20:31:58Z

Содержание ATS-6511A




















































































































Результаты поиска

Содержание ATS-6511A

Отзывы:

Symmetricom ATS-6511A, Руководство пользователя, Страница: 102 / 115

Результаты поиска

Содержание ATS-6511A

Отзывы: