Symmetricom ATS-6511A страница 60 Скачать руководство пользователя | Manualshive

Страница: 60 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

54

[type] pps

            [3]
               [format] B
               [signal_word] 0
               [type] irig
            [4]
               [format] B
               [signal_word] 0
               [type] irig

To check the status of the output card use the

status hardware:outputs:slots:N

command (N=Card

Slot #) to verify the card status.

      [ports]
         [1]
            [status] good
         [2]
            [status] good
         [3]
            [status] good
         [4]
            [status] good
      [power] enabled
      [type] 4394A

6.2.7 IRIG Outputs

The ATS-6511 is capable of providing different DC IRIG outputs on each port of the 4394A card
and AM IRIG outputs on the 4387A card.  By default ports #3 and #4 on the 4394A card are set
to B000.  The 4387A outputs are set to B120 by default.  Users can modify these settings.  Users
are  cautioned  to  ensure  they  connect  the  correct  cables  to  the  correct  output  ports  to  avoid  any
problems.

To verify the settings use the

settings hardware:slots:N

command (N=Card Slot #) to verify the

system settings.

ATS-6511> settings hardware:slots:1

      [tsc4373]
         [ports]
            [1]
               [pps_period] 1
               [pps_width] 1.000000000000000e-04
               [type] pps
            [2]
               [pps_period] 1
               [pps_width] 1.000000000000000e-04
               [type] pps

            [3]
               [format] B
               [signal_word] 0
               [type] irig
            [4]
               [format] B
               [signal_word] 0
               [type] irig

«
...
58
59
60
61
62
...
»

Содержание ATS-6511A




















































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS-6511A

Бренд: James Loudspeaker Страницы: 12

Бренд: QSC Страницы: 8

Бренд: Accuphase Страницы: 33

Бренд: Trek II Страницы: 2

Бренд: Kramer Страницы: 26

TUBE SCREAMER AMPLIFIER

Бренд: Ibanez Страницы: 52

Бренд: W.E.S.T. Elektronik Страницы: 48

Бренд: ATI Audio Страницы: 7

Бренд: Avatar Страницы: 16

GROOVE SLEUTH MK.II

Бренд: Phaedrus Audio Страницы: 9

Бренд: WORLD DESIGNS Страницы: 11

Бренд: Linear Страницы: 5

Бренд: VHT Страницы: 8

Бренд: Technics Страницы: 22

Бренд: SUPRO Страницы: 8

Бренд: Ude Страницы: 15

Бренд: Radial Engineering Страницы: 8

Бренд: Camco Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды