Symmetricom ATS-6511A страница 108 Скачать руководство пользователя | Manualshive

Страница: 108 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

102

•

network:

Network variables are values that specifically pertain to the network

settings  of the instrument.   They  are settable  by  the user  and  automatically  saved
when they are changed.  They are physically stored on the flash drive so changing
the flash will cause you to lose your network settings.  They are however preserved
during a software update.

•

settings:

Settings variables are values that are settable by the user. They are not

automatically saved however so the user must use the save command in order to
preserve the settings across a power cycle. Also note that they represent the
settings of the instrument and not necessarily the current state of the instrument.

•

status:

Status variable are values that indicate the current state of the instrument.

They are not settable by the user and can not be saved.

The show command can be used to view only a portion of the tree by requesting the
specific node within the hierarchy that you would like to view. For instance,

show

settings:gps

displays the current GPS settings for the instrument and

show status:gps

displays the current GPS status for the system.

Syntax

: show [--debug | [<-d | --depth> MAX_DEPTH] ] [NODE]

MAX_DEPTH limit display to MAX_DEPTH levels of data

(not available with the --debug option)

NODE

specifies a node to display

Command Example:

ATS-6511>show

See Also:

status, settings, network, config, save, load

Software Update:

Description:

Execute software update.

The software can be upgraded remotely using this command. The tflex-*.iso image must
be obtained from the Symmetricom ftp site

ftp.timing.com/pub/ATS-6511

. Use binary

transfer  mode  for  all  file  transfers.  Upload  the  image  to  the  unit  using  ftp  with  username
and  password  'update'.  Software  release  notes  for  each  version  are  also  available  in  the
same directory on the ftp site.

After  successful  completion  of  the  software  update,  the  unit  will  reboot,  system  settings
will be reset to their saved values, and hardware will undergo a complete reset, resulting in
the loss of output signals.

Syntax

: software_update <--ftp | --usb> [--file FILENAME] [--list]

--ftp   The updater searches for an ISO file in the upload directory.
        To upload an ISO file use FTP with username and password 'update'.
--usb   The updater searches for an ISO file on a USB drive.
        Not all units support connecting a USB drive.
--file  ISO file name, needed only if more than one ISO file is found.
--list  List available ISO files (list only; does not apply any update).

«
...
106
107
108
109
110
...
»

Содержание ATS-6511A




















































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS-6511A

Бренд: D.A.S. Страницы: 15

Бренд: E&I Страницы: 13

Бренд: Offel Страницы: 2

Бренд: Eden Страницы: 21

Бренд: McIntosh Страницы: 20

Бренд: Parasound Страницы: 8

openGear DEA-8205

Бренд: Ross Страницы: 32

Бренд: DAPAudio Страницы: 15

Бренд: Integra Страницы: 64

Бренд: Sonifex Страницы: 36

JBL PARTYBOX710

Бренд: Harman Страницы: 26

Бренд: PowerBass Страницы: 28

Бренд: AudioControl Страницы: 12

Бренд: Rompa Страницы: 4

Бренд: Harman Kardon Страницы: 11

Бренд: Macro-Tech Страницы: 41

Бренд: Massive Audio Страницы: 14

Бренд: L-Acoustics Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды