Symmetricom ATS-6511A страница 56 Скачать руководство пользователя | Manualshive

Страница: 56 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

50

Users can check the current system status using the

status fiber

and command to check the fiber

status.

ATS-6511B>status fiber

   [chassis_delay] 0.00000000000
   [clock_offset] -6.375066549999540e-11
   [da4340delay] 0.00000000000
   [fpga]
      [delay] 0.00000000000
   [inputA] good
   [inputB] good
   [steer] 9.385092999624222e-14
   [steer_before_sat_limit] -6.213664600386095e-13
   [steer_before_slew_limit] -6.213664600386095e-13
   [steer_control]
      [pll]
         [delta_from_nominal]
            [max_steer] 1.000000000000000e-04
            [max_steer_from_previous] 5.000000000000000e-07
         [enabled] true
         [fraction_of_nominal]
            [max_steer] 1.000000000000000e-11
            [max_steer_from_previous] 5.000000000000000e-14
         [gain] 1.000000000000000e-02
         [steer_mode] Slow
   [two_way]
      [channelA]
         [4340_output] 0
         [clock_offset] -6.375066549999540e-11
         [direct_connect] true
         [fiber_delay]
            [local] 6.797972759550001e-08
            [remote] 6.061995918399999e-08
         [remote_tdc_time] 2013-08-13-18:51:05
         [rxdelay] -3.786100000000000e-08
         [txdelay] -3.786100000000000e-08
      [channelB]
         [4340_output] 0
         [clock_offset] -8.851931372500003e-09
         [direct_connect] true
         [fiber_delay]
            [local] 1.471897352945000e-07
            [remote] 2.725690588240000e-07
         [remote_tdc_time] 2013-08-13-18:51:05
         [rxdelay] -3.746100000000000e-08
         [txdelay] -3.746100000000000e-08
   [two_way_serial_number] P044308
[OK] 2013-08-13T18:51:05Z

If the fault condition has cleared, users are able to check the events in the system using the

status

health:fiber_signal_present

command to check on events that occurred earlier.

ATS-6511B>status health:fiber_signal_present

   [active] false
   [cleared]
      [what] Fiber signal is present

«
...
54
55
56
57
58
...
»

Содержание ATS-6511A




















































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS-6511A

Бренд: Warfedale Pro Страницы: 12

Бренд: Traynor Страницы: 14

Бренд: Traynor Страницы: 16

Бренд: Toa Страницы: 12

Бренд: Technical Pro Страницы: 7

Бренд: AR Страницы: 62

Бренд: Sansui Страницы: 24

EVID C8.2 Ceiling

Бренд: Electro-Voice Страницы: 2

Бренд: AMERITRON Страницы: 19

Ininity INFDSP4425

Бренд: Harman Страницы: 34

Бренд: Plinius Страницы: 22

Бренд: Harman Kardon Страницы: 28

The One Limited Edition Amplifier

Бренд: Phoenix Gold Страницы: 8

Бренд: Decware Страницы: 18

Бренд: Rotel Страницы: 4

Power Director 4.7

Бренд: PS Audio Страницы: 12

Бренд: Rane Страницы: 4

Бренд: Dangerous Music Страницы: 11

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды