Symmetricom ATS-6511A страница 75 Скачать руководство пользователя | Manualshive

Страница: 75 / 115

background image

DOC 6511_Release K

ATS-6511A/B/C Users Guide

69

[when] 1998-01-01-00:06:52.834
[remote_tdc_starvation]

Issues with the data exchange over fiber

         [active] false
         [cleared]
            [what] Receiving remote TDCs
            [when] 2011-11-07-17:11:01.316
         [occurrences] 1
         [set]
            [what] Not receiving remote TDCs
            [when] 2011-11-07-17:10:39.722      [syscfg]
         [active] false
         [occurrences] 0
    [syscfg]
        [active] false
        [occurrences] 0

[tcxo_failure]

Internal Clock Failure

         [active] false
         [occurrences] 0
   [input]

Fiber Status

[switch] Auto Switch: A

Auto Switching in ON, Fiber A = Master

[kas2]

KAS2 Data

      [phase_step_count] 2
      [phase_sync_count] 1
      [ptd] 9.497872340000000e-09

Estimated UTC Offset

   [outputs]
      [enabled] true
   [reference]

6511B only

[frequency]
         [external]
            [communications] bad
            [locked] false
            [signal] missing
      [hp5071]
         [can_communicate] false
      [lns]
         [locked] true
      [ocxo_freq_control] 1
      [reference_frequency_estimate] Not Ready   [time] 2011-11-07-18:07:56

[unit]
[network]

Current network settings

[MAC] 00:A0:69:00:00:F8

Unit MAC Address

[broadcast] 192.168.150.255

Current Broadcast IP

[default_gateway] 192.168.150.1

Current Gateway Address

[ip] 192.168.150.71

Current IP Address

[netmask] 255.255.255.0

Current Subnet mask

[serial_number] 164233

Unit S/N

[start] 2011-06-09-21:21

Unit Start up (Date/Time Set)

[uptime] 18 hours, 38 minutes, 16 seconds

Amount of time 6511 has been running

[ver] tflex-5-1-0

Current Software Version

System Errors:

Alarms and events on the ATS-6511 are available via the

status

command. As

the events occur the system will

set

the alarm and time. Once the condition clears the system will

indicate the condition

cleared

, what the condition was, when it cleared and increment the

occurrence counter.

[clock_wander]
[active] false

[cleared]
[what] Clock wander is less than 100.000000ns

«
...
73
74
75
76
77
...
»

Содержание ATS-6511A




















































































































Отзывы:

Нет отзывов

Похожие инструкции для ATS-6511A

Бренд: B&K Страницы: 36

Бренд: B&K Страницы: 36

Бренд: B&K Страницы: 2

Бренд: B&K Страницы: 12

Бренд: B&K Страницы: 24

Бренд: Banner Страницы: 10

Бренд: L-Acoustics Страницы: 46

Бренд: L-Acoustics Страницы: 24

Бренд: Carson Страницы: 12

Бренд: Teac Страницы: 4

Бренд: Genz Benz Страницы: 8

Бренд: Fender Страницы: 9

dPatch SutterPatch

Бренд: Sutter Instrument Страницы: 2

Satcom Division VZC-6967 Series

Бренд: CPI Страницы: 140

Бренд: Sansui Страницы: 24

Бренд: Lightspeed Страницы: 26

Бренд: Rockbox Страницы: 2

Бренд: Harman Kardon Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды