SVS-Vistek evo1050 Скачать руководство пользователя страница 22

Страница: 22 / 88

Users Manual Area Scan Cameras SVSGigE

Page 22

Users Manual –evo1050, evo2050, evo2150, evo4050, evo4070, evo8050 and evo12040

4.4

Image

The image panel displays information about the picture geometry, the pixel clock and

it allows for the following settings:

•

AOI (area of interest) which can be less or equal the imager size

•

Binning mode (off, vertical, horizontal, 2x2)

No Binning

= full resolution: horizontal x 1, vertical x 1 (default setting)

H2 x V2 x: vertical 2 x and horizontal 2 x at the same time; Resolution: horizontal x

½, vertical x ½, Sensitivity is 4 x, pixel frequency is halved, max. frame rate is almost

doubled. “No Binning” sets the camera to full resolution, H1 x 2 and 2 x 1 binning is

also available

If you need other binning mode configurations consult factory or your nearest distrib-

utor.

Please note:

Using binning with a color version of the camera will cause incor-

rect colors and strange effects!

However, for fast focusing it might be useful.

•

Pixel depth (8-bit, 12-bit, 16-bit, if supported by camera)

•

Color (On/Off)

•

Bayer method (Disabled, Nearest neighbor, Simple, Bilinear, HQ Linear, Edge Sense,

Gray)

•

Factors for white balance (Red, Green, Blue)

•

“Balance” button for performing automatic white balance

•

“Equalize” button for setting all colors to 100%

•

Freeze (display switched off while acquisition continuous, for test purposes)

In addition the number of transferred frames is displayed as well as the number of

eventually lost frames. A frame loss may happen for example in case of an insufficient

network bandwidth or if the network connection gets interrupted for a short time or in

case of other network failures.

Further the number of resent network packets is displayed. The second number is the

last resent packet number and the first number indicates the total number of resent

packets.

4.5

Gain

The gain panel allows for adjusting gain and Autogain with the following controls:

The default gain setting is “0” dB. You may change the gain up to 6 dB (or higher) in steps of
1/10

. Note that the dark offset will increase and dynamic range will not be improved. Please note

that noise also is amplified. For good image quality do not increase gain more than 6 dB;

higher

Gain is possible but not specified!

4.6

Offset

Dark level offset adjustment is possible. When 8 Bit are transmitted it can be changed

from 0 to 255. Please note that factory adjustment is optimized for DR and sensitivity.

You may lose dynamic range. Alter only if you operate at high temperatures like +40

°C.

4.7

AutoGain/AutoExposure

Preliminary/Planned

Содержание evo1050

























































































Результаты поиска

Содержание evo1050

Отзывы:

Похожие инструкции для evo1050

Бренды по названию

Популярные бренды

SVS-Vistek evo1050, Руководство пользователя

Результаты поиска

Содержание evo1050

Отзывы:

Похожие инструкции для evo1050

Бренды по названию

Популярные бренды