Supero SUPERSERVER 8046B-6RF Скачать руководство пользователя страница 30

Страница: 30 / 104

3-4

UPER

ERVER 8046B-6RF/8046B-TRF User's Manual

3-4 Hard Drive Carrier LEDs

Each drive carrier has two LEDs that function when a drive has been installed:

SAS Drives

Green:

•

When illuminated, the green LED on the drive carrier indicates the drive

is powered on. When fl ashing it indicates data is being accessed on a drive.

If this LED is not lit, it means no power is being provided for the drive. Please

refer to Chapter 6 for instructions on replacing failed drives.

Red:

•

A solid red LED indicates a drive failure. If one of the drives fails, you

should be notifi ed by your system management software. Please refer to Chapter

6 for instructions on replacing failed drives. If this LED fl ashes ~ once per second

(1 Hz) it indicates RAID rebuilding activity.

SATA Drives

Green:

•

When fl ashing, the green LED on the drive carrier indicates drive activ-

ity. A connection to the backplane enables this LED to blink on and off when

that particular drive is being accessed.

Red:

•

The red LED to indicate a drive failure. If one of the drives fails, you should

be notifi ed by your system management software. Please refer to Chapter 6 for

instructions on replacing failed drives.

Содержание SUPERSERVER 8046B-6RF









































































































Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 8046B-6RF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды