Supero SUPERSERVER 8046B-6RF Скачать руководство пользователя страница 59

Страница: 59 / 104

Chapter 6: Advanced Chassis Setup

6-3

6-2 Control

Panel

The front control panel must be connected to the JF1 connector on the serverboard

to provide you with system status and alarm indications. A ribbon cable has bundled

these wires together to simplify this connection.

Connect the cable from JF1 on the serverboard (making sure the red wire plugs

into pin 1) to the appropriate connector on the front control panel PCB. Pull all ex-

cess cabling over to the control panel side of the chassis. The LEDs on the control

panel inform you of system status - see Figure 6-2 for details. See Chapter 5 for

details on JF1.

Figure 6-2. Front Control Panel LEDs

Power

NIC1

HDD

Power Fail

Overheat/

Fan Fail

Indicates power is being supplied to the system.

Indicates network activity on LAN port 1.

Indicates IDE device and hard drive activity. On the

SC748TQ-R1400BP, this LED indicates SAS or SATA drive

activity when fl ashing.

Indicates a power supply failure.

When this LED fl ashes, it indicates a fan failure. When on

continuously it indicates an overheat condition (see Chapter

3 for details).

NIC2

Indicates network activity on LAN port 2

Содержание SUPERSERVER 8046B-6RF









































































































Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 8046B-6RF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды