Supero SUPERSERVER 8046B-6RF Скачать руководство пользователя страница 92

Страница: 92 / 104

7-26

UPER

ERVER 8046B-6RF/8046B-TRF User's Manual

Current Mac Address in BMC

The BIOS will automatically enter the current Mac address in BMC for this ma-

chine; however it may be overwritten. Mac addresses are 6 two-digit hexadecimal

numbers (Base 16, 0 ~ 9, A, B, C, D, E, F) separated by dots. (i.e., 00.30.48.

D0.D4.60).

Subnet Mask Confi guration

Parameter Selector

This item displays the status of the Parameter Selector.

Subnet Mask

This item displays the current subnet mask setting for your IPMI connection. The

value of each three-digit number separated by dots should not exceed 255.

Current Subnet Mask in BMC

The BIOS will automatically enter the current subnet mask in BMC for this

machine; however it may be overwritten. The value of each three-digit number

separated by dots should not exceed 255.

Gateway Address

Parameter Selector

This item displays the status of the Gateway Address Parameter Selector.

Gateway Address

The BIOS will automatically enter the Gateway address of this machine; however

it may be overwritten. The value of each three-digit number separated by dots

should not exceed 255.

Current IP Address in BMC

The BIOS will automatically enter the current IP address in BMC for this machine;

however it may be overwritten. The value of each three-digit number separated

by dots should not exceed 255.

Remote Access Confi guration

Remote Access

This allows the user to enable the Remote Access feature. The options are Disabled

and

Enabled

. If Remote Access is set to Enabled, the following items will display:

Содержание SUPERSERVER 8046B-6RF









































































































Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 8046B-6RF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды