Supero SUPERSERVER 8046B-6RF Скачать руководство пользователя страница 3

Страница: 3 / 104

Preface

About This Manual

This manual is written for professional system integrators and PC technicians. It

provides information for the installation and use of the SuperServer 8025C-3R. In-

stallation and maintenance should be performed by experienced technicians only.

The SuperServer 8046B-6RF/8046B-TRF is a high-end quad processor server

based on the SC748TQ-R1400BP 4U tower/rackmount server chassis and the Su-

per X8QB6-F/X8QBE-F serverboard. The X8QB6-F/X8QBE-F supports four Intel®

Xeon processors. Please refer to our web site for an up-to-date list of supported

processors.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the

server system and describes the main features of the Super X8QB6-F/X8QBE-F

serverboard and the SC748TQ-R1400BP chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the server into a rack and

check out the server confi guration prior to powering up the system. If your server

was ordered without the processor and memory components, this chapter will refer

you to the appropriate sections of the manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

iii

Preface

Содержание SUPERSERVER 8046B-6RF









































































































Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 8046B-6RF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды