Supero SUPERSERVER 8046B-6RF Скачать руководство пользователя страница 27

Страница: 27 / 104

Chapter 3: System Interface

3-1

Power

The main power button is used to apply or remove power from the power supply

to the server system. Turning off system power with this button removes the main

power but keeps standby power supplied to the system.

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the control panel as well as others on the hard drive

carriers to keep you constantly informed of the overall status of the system as well

as the activity and health of specifi c components. There are also two buttons on

the chassis control panel and an on/off switch on the power supply. This chapter

explains the meanings of all LED indicators and the appropriate response you may

need to take.

3-2 Control Panel Buttons

There are two push-buttons located on the front of the chassis: a reset button and

a power on/off button.

Reset

Use the reset button to reboot the system.

Содержание SUPERSERVER 8046B-6RF









































































































Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 8046B-6RF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 8046B-6RF

Отзывы:

Похожие инструкции для SUPERSERVER 8046B-6RF

Бренды по названию

Популярные бренды