Supero SUPERSERVER 5010E Скачать руководство пользователя страница 49

Страница: 49 / 128

Chapter 5: Advanced Motherboard Setup

5-11

Quick Reference (for 5010H)

Jumpers

Description

Default Setting

JBT1

CMOS Clear

Pins 1-2 (Normal)

JP11/12

Front Side Bus Speed

Both: Pins 1-2 (Auto)

JP31

LAN2 Enable/Disable

Closed (Enabled)

JP32

Speaker En/Disable

Closed (Enabled)

JP35

LAN1 Enable/Disable

Closed (Enabled)

JPA1

SCSI Ch A Termination

Open (Terminated)

JPA2

SCSI Ch B Termination

Open (Terminated)

JPWAKE

Keyboard Wake-Up

Pins 1-2 (Disabled)

Connectors

Description

COM1/COM2

COM1/COM2 Serial Port Connector

CPU/CH/OH FAN

CPU/Chassis/Overheat Fan Headers

J1, J2, J3

Memory (DIMM) Slots

JA1

Ultra160 SCSI Conn. Channel A

JA2

Ext. Ultra160 SCSI Conn. Channel B

JA3

Ultra160 SCSI Conn. Channel B

J18, J19

IDE Hard Disk Drive Connectors

JP26

Floppy Disk Drive Connector

J29

ATX Power Connector

J30

PS/2 Keyboard/Mouse

J32, J33, J43, J51

Universal Serial Bus Ports

JF1

Front Control Panel

JL1

Chassis Intrusion Header

JOH

Overheat LED

JWOR

Wake-On-Ring Header

LAN1/LAN2

Ethernet Port 1/2

VGA

VGA Port (monitor)

WOL

Wake-on-LAN Header

Also see the figures on pages 5-4, 5-5 for the I/O ports and the
Front Control Panel (JF1) connectors.

Jumpers not indicated are for test purposes only.

(*Please refer to Sections 5-8, 5-9, and 5-10 for detailed informa-
tion on jumper settings and pin definitions.)

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды