Supero SUPERSERVER 5010E Скачать руководство пользователя страница 77

Страница: 77 / 128

Chapter 7: AMIBIOS

7-5

BIOS

CPU Overheat Warning

This option allows you to Enable or Disable a system overheat warning

signal, used to notify you in the event of a dangerous rise in heat levels.

CPU Overheat Warning

This option allows you to specify the temperature threshold that, when

exceeded, will trigger the overheat warning alarm.

The rest of the Health Monitor menu lists various voltages and temperatures

as they are currently being measured. These include CPU current tempera-

ture, CPU voltage, the RPMs of the CPU, H/W MonitorIN0 (CPU1), H/W

MonitorIN2 (+3.3V), H/W MonitorIN3 (+5V), H/W MonitorIN4 (+12v), H/W

MonitorIN5 (-12V), CPU Fan,Chassis Fan 1, Chassis Fan 2, and thermal

control fans. The settings are Enabled or Disabled.

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды