Supero SUPERSERVER 5010E Скачать руководство пользователя страница 32

Страница: 32 / 128

UPER

ERVER

5010H/5010E

Manual

3-2

3-3

Control Panel LEDs

The control panel located on the front of the SC810 chassis has five LEDs.

These LEDs provide you with critical information related to different parts of

the system. This section explains what each LED indicates when illumi-

nated and any corrective action you may need to take.

Overheat:

Indicates an overheat condition in the chassis. This may

be caused by cables obstructing the airflow in the system, or the ambient

room temperature being too warm. You should also check to make sure

that the chassis cover is installed and that all fans are present and operat-

ing normally. Finally, check the air seals for damage. The air seals are

located under the blower fan and beneath the frame cross section that

separates the drive bay area from the motherboard area of the chassis.

NIC2:

Indicates network activity on LAN2 when flashing.

NIC1:

Indicates network activity on LAN1 when flashing.

HDD:

Indicates IDE channel activity. On the SuperServer 5010H/

5010E, this light indicates CD-ROM drive activity when flashing.

NIC2

NIC1

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды