Supero SUPERSERVER 5010E Скачать руководство пользователя страница 107

Страница: 107 / 128

Chapter 7: AMIBIOS

7-35

BIOS

2nd Boot Device

The settings for the 2nd Boot Device are Removeable Device, Hard Drive,

ATAPI CDROM, Onboard LAN1Option and Onboard LAN2 Option.

3rd Boot Device

The settings for the 3rd Boot Device are Removeable Device, Hard Drive,

ATAPI CDROM, Onboard LAN1Option and Onboard LAN2 Option.

Hard Disk Drives

Use this screen to view the hard drives that have been auto-detected or

entered manually on your system.

Removeable Devices

Use this screen to view the removeable devices that have been auto-de-

tected or entered manually on your system.

ATAPI CDROM Drives

Use this screen to view the ATAPI CDROM drives that have been auto-

detected or entered manually on your system.

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды