Supero SUPERSERVER 5010E Скачать руководство пользователя страница 11

Страница: 11 / 128

Chapter 1

Introduction to the SuperServer 5010H/5010E

1-1

Overview

The Supermicro SuperServer 5010H/5010E is a high-end single processor,

1U rackmount server that features some of the most advanced technology

currently available. The SuperServer 5010H/5010E is comprised of two

main subsystems: the SC810 1U rackmount chassis and the or

single 370-pin Pentium III FCPGA or Celeron FCPGA/PPGA proces-

sor mainboard. Please refer to our web site for information on operating

systems that have been certified for use with the SuperServer 5010H/

5010E. (www.supermicro.com)

In addition to the mainboard and chassis, various hardware components

may have been included with your SuperServer 5010H/5010E, as listed

below.

One (1) 370-pin Pentium III FCPGA or one Celeron FCPGA/PPGA proces

sor*

One CPU heat sink

Up to 512 MB SDRAM (non-ECC supported, non-registered) main

memory

One (1) 1.44" floppy drive

One (1) slim CD-ROM drive

One (1) SCA SCSI backplane (5010H only)

Two (2) SCA SCSI drive carriers (5010H only)

SCSI Accessories (5010H only)

One (1) internal 68-pin Ultra160 SCSI cable for SCA SCSI backplane

One (1) set of SCSI driver diskettes

One (1) SCSI manual

Chapter 1: Introduction

1-1

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды