Supero SUPERSERVER 5010E Скачать руководство пользователя страница 67

Страница: 67 / 128

Chapter 6: Advanced Chassis Setup

6-5

SCSI Drive Installation (5010H only)

Mounting a SCSI drive in a drive carrier:

The SCSI drives are mounted in drive carriers to simplify their installation

and removal from the chassis. These carriers also help promote proper

airflow for the SCSI drive bays. For this reason, even empty carriers

without SCSI drives installed must remain in the chassis. To add a new

SCSI drive, install a drive into the carrier with the printed circuit board

side toward the carrier so that the mounting holes align with those in the

carrier. Secure the drive to the carrier with four screws, as shown in

Figure 6-4.

Figure 6-4. Mounting a SCSI Drive in a Carrier (5010H only)

Important: Regardless of how many SCSI hard drives

are installed, both SCSI drive carriers must remain in

the drive bays for proper airflow.

Use caution when working around the SCSI backplane.

Do not touch the backplane with any metal objects

and make sure no ribbon cables touch the backplane

or obstruct the holes, which aid in proper airflow.

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды