manualshive.com logo in svg

Supero SUPERSERVER 5010E, Руководство пользователя


Поделиться
Скачать
background image

Chapter 7: AMIBIOS

7-23

BIOS

C000, 16k Shadow

C400, 16k Shadow

C800, 16k Shadow

CC00, 16k Shadow

D000, 16k Shadow

D400, 16k Shadow

D800, 16k Shadow

DC00, 16k Shadow

These options specify how the 16 KB of video ROM at each of the above

addresses is treated.  The settings are Disabled, Enabled, and Cached/WP

. When Disabled, the contents of the video ROM are not copied to RAM.

When Enabled, the contents of 16 KB of video ROM beginning at the above

address are copied (shadowed) from ROM to RAM for faster application.

When set to Cached/WP, the contents of 16 KB of video ROM beginning at

the above address are copied (shadowed) from ROM to RAM and can be

written to or read from cache memory.  The settings for this option are

Disabled, Enabled and Cached/WP.  (The optimal settings are Cached/WP

for C000 and C400 and Disabled for all the other settings.

Содержание SUPERSERVER 5010E

































































































































Отзывы:

Нет отзывов

Похожие инструкции для SUPERSERVER 5010E

Canon ColorPASS-Z5000 Printing Manual preview
ColorPASS-Z5000
Бренд: Canon Страницы: 134
Canon imagePRESS Server G200 Service Manual preview
imagePRESS Server G200
Бренд: Canon Страницы: 82
Canon P 400 Service Manual preview
P 400
Бренд: Canon Страницы: 88
F5 ARX-2500 Installation Manual preview
ARX-2500
Бренд: F5 Страницы: 2
F5 WANJet 400 Appliance Upgrade Instructions preview
WANJet 400 Appliance
Бренд: F5 Страницы: 11
Leightronix UltraNEXUS-HD Flex Product Quick Manual preview
UltraNEXUS-HD Flex
Бренд: Leightronix Страницы: 5
IBM 88632SU User Manual preview
88632SU
Бренд: IBM Страницы: 100
PRG MBOX 2016 Hardware Manual preview
MBOX 2016
Бренд: PRG Страницы: 50
QNAP Turbo NAS TS-219P Troubleshooting Manual preview
Turbo NAS TS-219P
Бренд: QNAP Страницы: 49
Promise Technology PegasusPro R16 Product Manual preview
PegasusPro R16
Бренд: Promise Technology Страницы: 80
Viavi G3-GS-8P-288T Hardware Installation preview
G3-GS-8P-288T
Бренд: Viavi Страницы: 8
Comtrol DeviceMaster LT User Manual preview
DeviceMaster LT
Бренд: Comtrol Страницы: 136
IBM 220 Service Manual preview
220
Бренд: IBM Страницы: 68
IBM 206m - eServer xSeries - 8485 User Manual preview
206m - eServer xSeries - 8485
Бренд: IBM Страницы: 92
Black Box LES431A User Manual preview
LES431A
Бренд: Black Box Страницы: 60
TriLink AirProjector KJ-200 User Manual preview
AirProjector KJ-200
Бренд: TriLink Страницы: 56
Red Hat Linux Virtual Server Manual preview
Linux Virtual Server
Бренд: Red Hat Страницы: 82
R.V.R. Elettronica SpA TLC2000 User Manual preview
TLC2000
Бренд: R.V.R. Elettronica SpA Страницы: 128

Бренды по названию

Популярные бренды

Загрузить еще бренды