Supero SUPERSERVER 5010E Скачать руководство пользователя страница 98

Страница: 98 / 128

UPERSERVER 5010H/5010E

User's Manual

7-26

BIOS

Legacy USB Support

This option allows Legacy USB support. The settings are Disabled, En-

abled and Auto. Disabled prevents the use of any USB device in DOS or

during system boot. Enabled allows the use of USB devices during boot

and while using DOS. The Auto setting auto detects USB keyboards or mice

and if found, allows them to be utilized during boot and while using DOS.

PCI Slot1 IRQ Preferrence

PCI Slot2 IRQ Preferrence

PCI Slot3 IRQ Preferrence

PCI Slot4 IRQ Preferrence

The settings for the above options are Auto, 3, 4, 5 ,7, 9, 10, 11, 12, 14,

15.

IRQ 3

IRQ 4

IRQ 5

IRQ 7

IRQ 9

IRQ 10

IRQ 11

IRQ 14

IRQ 15

The settings for the above options are Available and Reserved. Available

allows the specified IRQ to be available for use by PCI/PnP devices. Re-

served means the specified IRQ is reserved for use by Legacy ISA de-

vices.

Содержание SUPERSERVER 5010E

































































































































Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды

Supero SUPERSERVER 5010E, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 5010E

Отзывы:

Похожие инструкции для SUPERSERVER 5010E

Бренды по названию

Популярные бренды