Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 3

Страница: 3 / 102

Preface

About This Manual

This manual is written for professional system integrators and PC technicians.

It provides information for the installation and use of the SuperServer 1026TT-

TF/1026TT-IBXF/1026TT-IBQF. Installation and maintenance should be performed

by experienced technicians only.

The SuperServer 1026TT-TF/1026TT-IBXF/1026TT-IBQF is a 1U Twin (two server-

boards in a 1U chassis) rackmount server based on the SC809TQ-1200B chassis

and two Super X8DTT-F/X8DTT-IBXF/X8DTT-IBQFserverboards.

Manual Organization

Chapter 1: Introduction

The fi rst chapter provides a checklist of the main components included with the

server system and describes the main features of the Super X8DTT-F/X8DTT-IBXF/

X8DTT-IBQF serverboard and the SC809TQ-1200B chassis.

Chapter 2: Server Installation

This chapter describes the steps necessary to install the SuperServer 1026TT-

TF/1026TT-IBXF/1026TT-IBQF into a rack and check out the server confi guration

prior to powering up the system. If your server was ordered without the processor

and memory components, this chapter will refer you to the appropriate sections of

the manual for their installation.

Chapter 3: System Interface

Refer to this chapter for details on the system interface, which includes the functions

and information provided by the control panel on the chassis as well as other LEDs

located throughout the system.

iii

Preface

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды