Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 97

Страница: 97 / 102

Appendix B: Installing Windows

B-1

Appendix B

Installing Windows

After all hardware components have been installed, you must fi rst confi gure Intel

South Bridge RAID Settings before you install the Windows OS and other software

drivers. To confi gure RAID settings, please refer to RAID Confi guration User Guides

posted on our web site at www.supermicro.com/support/manuals.

B-1 Installing Windows for a RAID System

Insert Microsoft's Windows XP/2003 Setup CD in the CD drive and the sys-

tem will start booting up from CD.

Press the <F6> key when the message "Press F6 if you need to install a third

party SCSI or RAID driver" displays.

When the Windows XP/2003 Setup screen appears, press "S" to specify ad-

ditional device(s).

Insert the driver diskette-"Intel AA RAID XP/2000/2003 Driver for ICH10R" into

the fl oppy drive and press the <Enter> key.

Choose the Intel(R) ICH10R

SATA RAID Controller

from the list indicated in

the XP/2003 Setup Screen, and press the <Enter> key.

Press the <Enter> key to continue the installation process. (If you need to

specify any additional devices to be installed, do it at this time.) Once all

devices are specifi ed, press the <Enter> key to continue with the installation.

From the Windows XP/2003 Setup screen, press the <Enter> key. The

XP/2003 Setup will automatically load all device fi les and then, continue the

Windows XP/2003 installation.

After the Windows XP/2003 OS Installation is completed, the system will auto-

matically reboot.

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды