Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 92

Страница: 92 / 102

7-26

UPER

ERVER 1026TT-TF/1026TT-IBXF/1026TT-IBQF User's Manual

Hard Disk Drives

This feature allows the user to specify the boot sequence from all available hard

disk drives. The settings are Disabled and a list of all hard disk drives that have

been detected (i.e., 1st Drive, 2nd Drive, 3rd Drive, etc).

1st Drive - [SATA: XXXXXXXXX]

•

Removable Drives

This feature allows the user to specify the boot sequence from available Removable

Drives. The settings are 1st boot device, 2nd boot device, and Disabled.

1st Drive - [USB: XXXXXXXXX]

•

2nd Drive

•

CD/DVD Drives

This feature allows the user to specify the boot sequence from available CD/DVD

Drives (i.e., 1st Drive, 2nd Drive, etc).

7-6 Exit

Options

Select the Exit tab from the AMI BIOS Setup Utility screen to enter the Exit BIOS

Setup screen.

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды