Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 60

Страница: 60 / 102

6-2

UPER

ERVER 1026TT-TF/1026TT-IBXF/1026TT-IBQF User's Manual

Figure 6-2. Chassis Rear View

6-2 Control

Panel

Each control panel on the front of the chassis must be connected to the JF1 con-

nector on its assiciated serverboard to provide you with system control buttons and

status indicators. (When viewed from the front of the chassis, the serverboard on

the left is referred to as the primary serverboard and the serverboard on the right

as the secondary.)

These wires have been bundled together in a ribbon cable to simplify the connection.

Connect the cable from JF1 on the serverboard to the control panel PCB (printed

circuit board). Make sure the red wire plugs into pin 1 on both connectors. Pull all

excess cabling out of the airfl ow path. The LEDs inform you of system status for

the serverboard it is connected to. See Chapter 3 for details on the LEDs and the

control panel buttons. Details on JF1 can be found in Chapter 5.

Figure 6-1. Chassis Front View

USB Ports COM Port VGA Port UID Button

UID Button

LAN Ports

Dedicated IPMI Port

Power Supply

PCI-Exp x16 Slot

SATA Drives

Control Panel: Primary Serverboard

Control Panel: Secondary Serverboard

USB Ports COM Port VGA Port

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды