Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 62

Страница: 62 / 102

6-4

UPER

ERVER 1026TT-TF/1026TT-IBXF/1026TT-IBQF User's Manual

6-4 Air

Shrouds

Air shrouds concentrate airfl ow to maximize fan effi ciency. The SC809 chassis air

shroud does not require screws to set up. Two identical air shrouds are needed in

the system, one for each node.

Note:

the air shroud is intended for use with passive CPU heatsinks only. When

using active heatsinks, you should remove the air shroud.

Installing the Air Shrouds (Figure 6-4)

Confi rm that all six fans are in place and working properly

Place the fi rst air shroud into the chassis. The air shroud sits behind the

system fans. Each air shroud covers three fans.

Install the second air shroud in the same manner as the fi rst.

Figure 6-3: Replacing a System Fan

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды