Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 48

Страница: 48 / 102

5-14

UPER

ERVER 1026TT-TF/1026TT-IBXF/1026TT-IBQF User's Manual

Reset Connector

The reset connector is located on pins

3 and 4 of JF1 and attaches to the

reset switch on the computer chas-

sis. See the table on the right for pin

defi nitions.

PW_ON Connector

The PW_ON connector is on pins 1

and 2 of JF1. This header should be

connected to the chassis power but-

ton. See the table on the right for pin

defi nitions.

5-9 Connector

Defi nitions

ATX Power Connector

The main ATX power supply connec-

tors on the X8DTT-F/X8DTT-IBXF/

X8DTT-IBQF are proprietary 20-pin

connections. Refer to the table on

the right for the pin defi nitions. Only

one of the two ATX power connectors

from each serverboard should be con-

nected to the power supply

Reset Button

Pin Defi nitions (JF1)

Pin# Defi nition

Reset

Ground

Power Button

Pin Defi nitions (JF1)

Pin# Defi nition

PW_ON

Ground

Auxiliary Power Connector

A 4-pin 12V auxiliary power connector

is included to provide power to hard

drive disks. See the table on the right

for pin defi nitions.

Auxiliary Power

Pin Defi nitions (JP10)

Pin# Defi nition

+12V

Ground

+5V

ATX Power 20-pin Connector

Pin Defi nitions (ATX Power 1/2)

Pin# Defi nition Pin # Defi nition

PS On

Ground

5VSB

Ground

NC2

NC1

12V

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды