Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 27

Страница: 27 / 102

Chapter 3: System Interface

3-1

Chapter 3

System Interface

3-1 Overview

There are several LEDs on the two control panels and on the hard drive carriers to

keep you constantly informed of the overall status of the system as well as the activ-

ity and health of specifi c components. There are also two buttons on each control

panel. This chapter explains the meanings of all LED indicators and the appropriate

response you may need to take. Note that the server has two control panels, one

for each serverboard installed in the system. This allows each serverboard to be

controlled independently of the other.

3-2 Control Panel Buttons

There are two push-buttons located on each control panel: a reset button and a

power on/off button.

Reset

Depressing the reset button will reboot only the serverboard it is associated with.

Power

This is the main power button, which is used to apply or turn off the main system

power only to the serverboard it is connected to. Depressing this button removes

the main power but keeps standby power supplied to the serverboard.

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды