Supero SUPERSERVER 1026TT-IBQF Скачать руководство пользователя страница 61

Страница: 61 / 102

Chapter 6: Advanced Chassis Setup

6-3

6-3 System

Fans

Each serverboard has its own set of three 4-cm high-performance PWM fans (for

a total of six in the chassis) to provide the cooling for the system. Fan speed may

be controlled by a setting in BIOS (see Chapter 7).

System Fan Failure

If a fan fails, the remaining fans will ramp up to full speed and the overheat/fan fail

LED on the control panel will blink on and off. Replace any failed fan at your earli-

est convenience with the same type and model (the system can continue to run

with a failed fan). Remove the top chassis cover while the system is still running to

determine which of the fans has failed. The system fans are hot-swappable. There

is no need to power down the system when switching fans.

Changing a System Fan (Figure 6-3)

If necessary, open the chassis while the power is running to determine which

fan has failed. (Never run the server for an extended period of time with the

chassis open.)

Remove the failed fan's power cord from the serverboard.

Lift the fan housing up and out of the chassis.

Gently push the fan upwards from underneath the fan housing to remove it.

Place the new fan into the vacant space in the housing while making sure

the arrows on the top of the fan (indicating air direction) point in the same

direction as the arrows on the other fans. Make sure that all four of the fan's

rubber feet are in place.

Replace the fan housing back into the chassis.

Reconnect the wiring.

Confi rm that the fan is working properly before replacing the chassis cover.

Содержание SUPERSERVER 1026TT-IBQF







































































































Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды

Supero SUPERSERVER 1026TT-IBQF, Руководство пользователя

Результаты поиска

Содержание SUPERSERVER 1026TT-IBQF

Отзывы:

Похожие инструкции для SUPERSERVER 1026TT-IBQF

Бренды по названию

Популярные бренды